Suction

825 m3/h︱power capacity 1,2 kW︱Dimensions (L/W/H) 1210 x 800 x 900 mm︱weight 108 kg︱

---

1860 m³/h︱ Pressung 2.900 Pa︱ 1,1 kW︱filter surface area 10 m²︱ 72 dB(A)︱ 400/50 V/Hz︱ 665 x 1100 x 1495 mm︱ 200 kg︱

---

- Hose arm 3 m, joints inside - Filter cartridge: dust class M - Pre-filter: baffle plate - Current type: 3Ph+N+PE The filter system --------------------------------------- The mobile filter system of the Cartmaster IFA type is thanks to the automatic Cleaning particularly suitable for welding work with unalloyed and alloyed steels, galvanized material and aluminum with heavy smoke development. It corresponds to the safety requirements for devices Welding fume class "W3" (high-alloy steels with alloy components > 30% Nickel-based alloy).If used as intended, the system can be used for the Recirculation mode used because the requirements for the Exceptions according to TRGS 560 are fulfilled. That special developed, dirt-dependent cleaning system ensures a good cleaning behavior of the filter cartridge, so that an optimal suction performance is guaranteed throughout the operation. The cleaned particles fall into a dust collection drawer from which they can then be disposed of. The powerful spiral fan ensures even with saturated Filter cartridges for a high volume flow. The filter media --------------------------------------- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ------------------------ The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

2500 m³/h︱ 2500 kPa︱volume capacity 1600 m³/h︱feed volume > 99 %︱ 1,1 kW︱ 72 dB(A)︱ 0,58 x 0,58 x 0,9 m︱ 80 kg︱ 230 V / 50 Hz V︱

---

Particle pre-separator: coarse filter, pre-filter Main particle separator: main filter Gas separator: activated carbon filter Hose arm: joints inside What is the filtoo? The filtoo filter device newly developed by TEKA is a mobile filter system, for many tasks in the area of ??filtration of smoke and dust and gases can be used. The device was based on DIN EN ISO 15012-1 (2005) tested and is IFA (formerly BGIA) certified (IFA No. 201020469/1140) for welding smoke class "W3" (degree of separation:> 99.9%). at The filtoo is intended to be used for the separation of smoke suitable, which by welding separation and joining processes at the Machining of unalloyed steels, including high-alloy chrome / Nickel steels are released. How does the filtoo work? The Polluted air sucked into the filter system. In a multi-level The filter process filters the particles / gases from the air stream and the clean air is fed back into the work area. Where can the filtoo be used? At welding workplaces, in the workshop area, for soldering applications, at Restorers and locksmiths. What do you get for your money? All you get is a completely ready-to-use "plug and play system" the recording device must be connected before commissioning. How is the filtoo set up? The housing is made of a stable sheet steel construction and is inside as well as provided with a powder coating on the outside. The filter elements are over A maintenance hatch is accessible and can therefore be accessed very easily and quickly can be removed. The system has functional controls.

400 V / 50 Hz ︱ < 75 dB(A) ︱power capacity 15 kW︱volume capacity 20.000 m³/h︱weight 1590 kg︱

---

Modular plug & play airtower for hall extraction of welding fumes with integrated, soundproofed Fan, automatic, differential pressure controlled Filter cleaning, system control with color display, particle pre-separation and IFA - tested filter cartridges. The system is for a volume flow of average 20,000 m³ / h designed 1st filter stage - main filter: Filter area: 222 m² Number of filters: 6 pieces Dust class according to DIN EN 60335-2-69: M. Degree of separation:> 99.9% Cleaning: Jet - Pulse Compressed air connection: NW 7.2 mm, 4-6 bar, oil and water free 2nd filter stage - fine dust filter. Filter area: 65 m² Filter class according to ISO 16890: ISO ePM1 80% 3rd filter stage - Synthetic fiber mats: Filter area: 8 m² Filter class according to ISO 16890: ISO coarse 60% Total filter area: 295 m² Dimensions: Width filter unit: 2,066 mm Depth filter unit: 1,756 mm Height of filter unit: 3,643 mm Dust container: 200 liters Version Sanders incl .: - NOVUS efficiency package FT20.000 - timer - NOVUS particle sensor

1860 m³/h︱ Pressung 2.900 Pa︱ 1,1 kW︱filter surface area 10 m²︱ 72 dB(A)︱ 400/50 V/Hz︱ 665 x 820 x 1365 mm︱ 165 kg︱

---

mobile extraction, welding fume extraction (manual cleaning by loss of pressure) - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Particle pre-separator: baffle plate - Current type: 3Ph+N+PE The filter system --------------------------------------- The mobile filter system of the type StrongMaster IFA is particularly suitable for Welding work with unalloyed and alloyed steels, galvanized material and Aluminum in case of heavy smoke development. She corresponds to the Safety requirements for devices in the welding fume class "W3" (high-alloy steels with alloy components > 30% nickel-based alloy). When used as intended, the system can be used for be used in the recirculation mode, since the requirements for the Exceptions according to TRGS 560 are fulfilled. The filter will via a maintenance door using a compressed air gun from the clean air side cleaned. The cleaned particles fall into a dust collection drawer from the they can then be disposed of. The powerful scroll fan ensures a high volume flow even with saturated filter cartridges. The filter media --------------------------------------- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ------------------------ The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

table dimensions 1000x500 mm︱power capacity 1,35 kW︱

---

In our opinion, the machine is in very good condition and can be viewed by appointment. ***Accessories, tools and clamping devices shown are only part of the scope of delivery if this is noted in the additional information.*** *** Changes and errors in the specifications and information, as well Subject to prior sale! ***

gebraucht ︱ 2015 ︱ 2360A ︱ prompt, Zwischenverkauf v ︱ Türkei ︱ 7900 €︱ 1 ︱ 2500 m³/h︱ 40 m²︱ 3300 Pa︱ 4 kW︱ 2084 mm︱ 1260 mm︱ 1840 mm︱ 525 kg︱

---

8 pcs. filter elements filter cleaning by air-shock filter differential pressure monitoring filter control by possible CNC internal spark separator 80 l dirt container users manual in ENGLISH

air flow quantity 2500 m³/h︱suction power . kPa︱power capacity 1,1 kW︱

---

Sweat extractionThe techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us.

air flow quantity . m³/h︱suction power . kPa︱power capacity 2,2 kW︱

---

Sweat extractionThe techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us.

power capacity 7,5 kW︱ . ︱ Schweißarbeitsplatz ︱ 113112 ︱

---

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

volume capacity 1800 m³/h︱power capacity 2,2 kW︱turning speeds 2600 U/min︱

---

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

extraction capacity: 1200 m³ / h
drive: 0.75 kW
space requirement: 700 x 660 x 1030 mm
Nugbwpet

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

Extraction capacity: 1200 m³ / h
Bjljxyczux
Drive: 0.75 kW
Space requirement: 700 x 660 x 1030 mm

weight 35 kg︱negative pressure 125 kp/m²︱ 300 m³/h︱

---

Extraction, Type: Sto 5/125, Manufacturer: WMW, Year of manufacture: 1969,

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

Inlet diameter: 55 mm
1 suction speed
Becnc3xw7x
Electr. Connection: 230 V
Space: 700 x 280 x 370 mm

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

Flow Max: 220 m³/h
Pressure Max 22000 PA
Electr. Connection: 230 V
Weight: 16.5 kg
Ryaneezb7
Space requirements: 720 x 320 x 410 mm

air flow quantity . m³/h︱suction power . kPa︱power capacity 2,2 kW︱

---

Sweat extractionThe techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us.

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

Suction power of the appliance: 182 m³/h
with 5 m 45 air hose Ø: 159 m ³/h
Filter surface: 9.6 m2
Electr. Connection: AC 220 V
Weight: 20 kg
Space: 850 x 330 x 450 mm
Vqqg7y

air flow quantity m³/h︱suction power kPa︱power capacity kW︱

---

extraction capacity: 1250 m³/h
filter area: 50 m²
space needed: 1200 x 800 x 900 mm
weight: 108 kg
Beu0odoili

air flow quantity 1650 m³/h︱suction power . kPa︱power capacity 0,75 kW︱

---

air flow quantity . m³/h︱suction power . kPa︱power capacity 16 kW︱

---

The tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us.