MEB Maschinenhandel GmbH - Stockist for used machines
Machinelist:
Injection-moulding machine (rubber)
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B210304 · Injection-moulding machine (rubber)
ENGEL - ES 200V/45 VT-Elast - - 2010 -
Technical details
Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive power: 11 kW - Weight without oil: 6,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B210803 · Injection-moulding machine (rubber)
ENGEL - ES 200/45 VTHL - - 2004 -
Technical details
Condition: used, Specification: C-frame injection moulding machine for TPE - used, from testing department Including PIOVAN dosing unit clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - Clear width: 585 mm - Tool installation height min.: 185 mm - Max. stroke: 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 4 - Ejector stroke: 200 mm Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B220302 · Injection-moulding machine (rubber)
ENGEL - ES 200/25 VHL - - 2003 -
Technical details
Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B210303 · Injection-moulding machine (rubber)
ENGEL - ES 200V/45 VT-Elast - - 2001 -
Technical details
Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive power: 15 kW - Weight without oil: 5,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B230701 · Injection-moulding machine (rubber)
ENGEL - ES 330/80 LIM - - 1993 -
Technical details
Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 185 l - Weight approx.: 4.000 kg
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-B230702 · Injection-moulding machine (rubber)
ENGEL - ES 330/80 LIM - - 1991 -
Technical details
Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar - Specific injection pressure increased: 2200 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN - Control: CC 90-A02 Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 155 l - Weight approx.: 3,100 kg
Datasheet
Request / Contact
Injection-moulding machines (plastic)
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-L200203 · Injection-moulding machines (plastic)
ENGEL - VC 80H/80L / 130 Combi - - 2006 -
Technical details
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-L200202 · Injection-moulding machines (plastic)
ENGEL - ES 1350 H 500 W/400 HL-2 F - - 2005 -
Technical details
Condition: used, Specification: horizontal injection moulding machine, factory no: Injection unit 1: - screw diameter: 60 mm - metering stroke: 200 mm - Screw speed: 226 rpm - Injection flow: 351 cm³/sec - Injection volume: 735 cm³ - Spec. injection pressure: 1.489 bar - Spec. injection pressure increased: 2,011 bar Injection unit 2: - Screw diameter: 40 mm - Metering stroke: 140 mm - Screw speed: 400 rpm - Injection flow: 197 cm³/sec - Injection volume: 251 cm³ - Spec. injection pressure: 1.286 bar - Spec. injection pressure increased: 2.029 bar Clamping unit: - Clamping force max.: 4,000 kN - Clamping platens: 1,400 x 1030 mm - Opening stroke: 954 mm - Max. platen distance: 1,520 mm - Ejector stroke: 250 mm - Ejector force: 83.0 kN - Connected load: 193 kW - Operating hours: 93421 hours - Hydraulic core pull: 2 FAP 4 BAP Handling: ERC 84/1-E RC 100 integrated
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-L191105 · Injection-moulding machines (plastic)
ENGEL - ES 750/200 W/250 HL 2F - - 1997 -
Technical details
Condition: used, Specification: Horizontal injection moulding machine, Factory No.: 30883 Injection unit 1: - Screw diameter: 50 mm - Dosing stroke: 200 mm - Screw speed: 240 rpm - Injection flow: 291 cm³/sec - Injection volume: 392 cm³ - Injection weight: 353 g - Special injection pressure: 1,430 bar - Special injection pressure increased: 1,900 bar - Nozzle path: 650 mm - Heating capacity: 15,3 kW - Number of heating zones incl. nozzle: 5 Injection unit 2: - Screw diameter: 25 mm - Dosing stroke: 140 mm - Screw speed: 480 rpm - Injection flow: 88 cm³/sec - Injection volume: 69 cm³ - Injection weight: 61 g - Special injection pressure: 2,000 bar - Special injection pressure increased: 2,400 bar - Heating capacity: 6,6 kW - Number of heating zones incl. nozzle: 6 Clamping unit: - Clamping force max.: 2,500 kN - Mounting plates BAP: 1,150 x 905 mm HL - FAP clamping plates: 1,150 x 1,030 mm - Opening stroke: 850 mm - Distance between plates max.: 1,200 mm - Ejector travel: 200 mm - Ejector force: 83.0 kN Drive: - Pump drive power: 45 kW - Operating hours: 92680 hours Handling: ERC 63/1C integrated
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-L200401 · Injection-moulding machines (plastic)
ENGEL - ES 700 / 175 STND - - 1992 -
Technical details
Condition: used, Specification: Horizontal injection moulding machine, Injection unit: - Screw diameter: 45 mm - Screw length L/D: 20 - Spray volume: 318 cm³ - Shot weight max.: 287 g - Special spraying pressure: 2,100 bar Clamping unit: - Max. clamping force: 1,750 kN - clamping plates: 700 x 700 mm - Opening path max.: 460 mm - mould installation height: 150 mm - Operating hours: 89217 h - 1x core puller - Handling / Robots: ENGEL
Datasheet
Request / Contact
- MEB Maschinenhandel GmbH
- Schwalbenweg 4
- 30826 Garbsen
- Deutschland
-
(0)5031 9394-634
-
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
#2037-L210203 · Injection-moulding machines (plastic)
ENGEL - insert 500H/200 ROTARY - - 12/2016 -
Technical details
Condition: used, very good condition Specification: Vertical injection moulding machine, with rotary table injection unit: - screw diameter: 40 mm - injection volume: 251 cm³ - Injection flow: 244 cm³/sec - Spec. injection pressure: 1,300 bar - Spec. injection pressure increased: 2,020 bar - Nozzle stroke: 500 mm - Nozzle pressure: 51.9 kN Clamping unit: - Clamping force max.: 2,000 kN - Clamping platens hor. x vert. 820 x 459 mm - Max. platen distance: 880 mm - Opening stroke: 400 mm - Mould installation height: 480 mm - Ejector stroke: 105 mm Number of heating zones incl. nozzle: 4 - Heating power: 9.3 kW - Weight clamping unit: 11,000 kg - Weight injection unit: 3.500 kg - Weight total: 14.500 kg - Operating hours approx.: 643 hours
Datasheet
Request / Contact
MEB Maschinenhandel GmbH
Schwalbenweg 4
Contact Trader
MEB Maschinenhandel GmbH
Schwalbenweg 4
30826 - Garbsen
Deutschland
(0)5031 9394-634
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
Contact person:
Schwalbenweg 4
30826 - Garbsen
Deutschland
(0)5031 9394-634
info@meb-maschinenhandel.de
www.meb-maschinenhandel.de
Contact person:
Machine category
Anlagen, komplett · Extruder Gummi · Extruder Kunststoff · Gummi-Spritzgussmaschine · Kalander · Mischer · Mooney Viscometer · Raupenabzug Bandabzug · Rheometer · RPA (Rubber Process Analyzer) · Schneidmaschinen · Sonstiges · Spitzgussmaschinen (Kunststoff) · Vulkanisierpresse · Walzwerk · Zugprüfmaschine ·